DigiPlus stock

List of contents of this article:

• 1,DigiPlus stockWhat does the front assistant on the Volkswagen cc dashboard mean
• 2, What does car pcs mean
• 3, Where is the Lexus pcs switch
• 4. Jetta vHow to turn on the s5 pre-collision system

What does the front assist on the Volkswagen cc dashboard mean

The front assist is Volkswagen's urban emergency braking system, also known as bump Crash warning safety system. It can be seen from the name that the main function of this function is emergency braking, which is similar to the active braking function.

The front auxiliary is Volkswagen's urban emergency braking system, also known as the collision warning safety system. It can be seen from the name that the main function of this function is emergency braking, which is similar to the active braking function. However, the trigger conditions of the front-end auxiliary system are very harsh.

According to the inquiry of Pacific Automobile, Volkswagen Baolai front auxiliary refers to a safety system equipped by Volkswagen for its Baolai models.The system is mainly used to avoid collisions between vehicles during driving, especially when driving and stopping at low speeds.

The front auxiliary is not available refers to the failure or failure of the front auxiliary system (such as anti-collision warning, automatic emergency braking, etc.) installed on the vehicle. This may be caused by sensor failure, electrical problems, software errors or other technical failures.

What does car pcs mean

1. Car dashboard pcs is a pre-collision system, also known as a pre-safety protection system. It can automatically detect obstacles ahead and calculate the possibility of collisions. If the system judges that the collision is very likely, it will sound an alarm to remind the driver.

2. The pcs on the car mainly refers to the pre-collision safety system.When the light of the system is on, it means that the pre-collision safety system has been turned off or there has been a problem with the system. Generally, the key to the pcs system is under the steering wheel. When the pcs function is turned on, the indicator light will turn off.

3. Automobile PCS is a pre-collision safety system, the full name of which is "reversing anti-collision radar", also known as "parking assistance device". The sensor of the system is a radar installed in the front of the car, which can automatically detect obstacles in front of you and measure the probability of collision.

4. PCS is the abbreviation of Power Control System, that is, the power control system, which is very common in modern cars. When the system detects a fault, the PCS warning light of the vehicle will light up, which means that you need to quickly find the problem and fix it.

5. What does pre-collision system (PCS) mean: Introduction The pre-collision system can automatically detect obstacles ahead and calculate the possibility of collision. If the system judges that the possibility of collision is high, an alarm will be issued.

Where is the Lexus pcs switch

On the dashboard on the left side of the steering wheel.The Lexus es350 anti-skid switch is located on the dashboard on the left side of the steering wheel of the car, which can be seen by opening the driver's door.

The switch button of the PCS system is usually located under the steering wheel. When the PCS function is turned on again, the indicator light will go out. Toyota's pre-collision system is one of the earliest brands to be equipped with this system in mass-produced cars, which was first used in Toyota's Lexus LX and RX models. The sensor of the system is a millimeter-wave radar installed in the front of the car.

When the light of the system is on, it means that the pre-collision safety system has been turned off or there is a problem with the system. Generally, the key to the pcs system is under the steering wheel. When the pcs function is turned on, the indicator light will turn off.

How to turn on the pre-collision system of Jetta vs5

1. The method of turning on the pre-collision safety system is as follows: First, start the vehicle, press the button on the right side of the ok button on the left side of the steering wheel, find the setting button on the instrument, and press the direction The key is to find pcs, and then press the ok button on the left side of the steering wheel to turn on the pcs pre-collision system. Press the OK button for a long time to adjust the sensitivity of pcs in three gears.

2. Restart the engine, briefly press the ESPOFF button on the vehicle to see if the ESP is turned off by mistake; go to the 4S store for maintenance, use a special fault diagnostic device to find the fault, and remove the fault code with the decoder after repair to ensure that the ESP works normally and the fault light It will be extinguished.

3. The steps to activate the car system are as follows: you need to enter the car and start it. After opening the driving information interface, slide the interface to find the settings and click to enter. In the vehicle setting interface, find the pcs option, that is, the pre-collision system, and the status is set to off. Click the OK button, and the pre-collision system will start.

4. Start the vehicle first, press the button on the right side of the ok key on the left side of the steering wheel, find the setting button on the instrument, press the direction key to find the pcs, and then press the ok key on the left side of the steering wheel, set to turn on the pcs pre-collision system, and press the ok key for a long time to adjust the sensitivity of pcs in three steps.