Bingo Plus stock

List of catalogs of this article:

• 1,Bingo Plus stock< A href='#How is the engine, gearbox and semi-axle connected' title='How is the engine, gearbox and semi-axle connected'>How is the engine, gearbox and semi-axle connected
• 2, How to connect the Lego sixteen-cylinder engine with the six-speed gearbox in reverse
• 3, How to connect the engine and gearbox of the shovel?

How are the engine, gearbox and semi-axle connected

Car engines and gearboxes are connected together.The car engine and the gearbox are connected by a transmission shaft (also known as the drive shaft). The transmission shaft transmits the power of the engine to the gears and clutches in the gearbox, thus controlling the speed and power of the vehicle.

The connection method of the engine and the gearbox is: first lift the engine, and then lift the gearbox; the operator slowly aligns and assembles them together through the positioning pin and core shaft on the engine and gearbox; and then tightens the connection bolts on the engine and gearbox.

The half-shaft is not directly connected to the gearbox, but directly connected to the hub and differential.

When the engine is working, the flywheel and the pump wheel rotate together, driving the oil in the pump to drive the turbine impeller to rotate. It's like putting two fans together face to face, turning on one fan, and the other fan will also rotate.The guide wheel makes the oil thrown by the turbine hit the pump wheel again, increasing the torque.

How to connect the reverse gear of the Lego 16-cylinder engine with the six-speed gearbox

Assemble the shell of the six-speed gearbox. Assemble gears and shafts. Assemble the internal structure of the shell. Add a motor, including a motor and a battery box. Connect the motor and the shaft. Add wheels. Conduct a test.

When the engine is working, the flywheel and the pump wheel rotate together, driving the oil in the pump to drive the turbine impeller to rotate. It's like putting two fans together face to face, turning on one fan, and the other fan will also rotate. The guide wheel makes the oil thrown by the turbine hit the pump wheel again, increasing the torque.

The gearbox is a gearbox that changes the transmission ratio and direction of movement.It is located between the clutch and the central transmission. The main functions are: changing the driving force and driving speed of the vehicle (shifting gears) when the engine speed and torque remain unchanged; so that the vehicle can drive backwards (change direction); the engine can stop without turning off (idling gear).

It enables cars to drive at a very low and stable speed, and this kind of. It is difficult to achieve a low speed by relying on the minimum stable speed of the internal combustion engine alone; the reverse gear of the gearbox allows the car to drive backwards; its neutral gear allows the car to separate the engine from the transmission system for a long time when starting the engine, stopping and taxiing, etc.

Reverse the gear in the sixth or seventh gear, marked with a capitalized R. After stepping on the clutch, just hang directly into the position marked R, which is the most common reverse gear method. Press down, and then hang the reverse gear. Some cars need to press the gear down when hanging the reverse gear.

The reverse gear needs to be pressed down with a certain force. Press and hold it and push it forward to the left at the same time. If you don't press it, it will be the first gear. This down-pressing action can be understood as unlocking the reverse lock. The chance of hanging wrong should be 0, unless the driver is dizzy.

How to connect the engine and gearbox of the shovel?

1. Engine power can be conducted to the gearbox through the clutch. Power can also be transmitted to the gearbox through the hydraulic torque converter.

2. The connection method of the engine and the gearbox is: first hoist the engine, and then lift the gearbox; the operator slowly aligns and assembles them together through the positioning pin and core shaft on the engine and gearbox; and then tightens the connection bolts on the engine and gearbox.

3. When the engine is working, the flywheel and the pump wheel rotate together, driving the oil in the pump to drive the turbine impeller to rotate. It's like putting two fans together face to face, turning on one fan, and the other fan will also rotate. The guide wheel makes the oil thrown by the turbine hit the pump wheel again, increasing the torque.